Miniature Optical Fiber Fabry-Perot Interferometer Based on a Single-Crystal Metal-Organic Framework for the Detection and Quantification of Benzene and Ethanol at Low Concentrations in Nitrogen Gas.

This study reports for the first time, to the best of our knowledge, a real-time detection of ultralow-concentration chemical gases using fiber-optic technology, combining a miniaturized Fabry-Perot interferometer (FPI) with metal-organic frameworks (MOFs). The sensor consists of a short and thick-walled silica capillary segment spliced to a lead-in single-mode fiber (SMF), housing a tiny single crystal of HKUST-1 MOF, imparting chemoselectivity features. Ethanol and benzene gases were tested, resulting in a shift in the FPI interference signal. The sensor demonstrated high sensitivity, detecting ethanol gas concentrations (EGCs) with a sensitivity of 0.428 nm/ppm between 24.9 and 40.11 ppm and benzene gas concentrations (BGCs) with a sensitivity of 0.15 nm/ppm between 99 and 124 ppm. The selectivity study involved a combination of three ultralow concentrations of ethanol, benzene, and toluene gases, revealing an enhancement factor of 436% for benzene and 140% for toluene, attributed to the improved miscibility of these conjugated ring molecules with the alkane chains of the ethanol-modified HKUST-1. Experimental tests confirmed the sensor's viability, demonstrating significantly improved response time and spectral characteristics through crystal polishing, indicating its potential for quantifying and detecting chemical gases at ultralow concentrations. This technology may prevent energy resource losses, and the sensor's small size and robust construction make it applicable in confined and hazardous locations.

Miniaturized fluorescence pH sensor with assembly free ball lens on a tapered multimode optical fiber.

In biochemistry, the absence of a compact, assembly-free pH sensor with high sensitivity and signal-to-noise ratio has been a persistent hurdle in achieving accurate pH measurements in real time, particularly in complex liquid environments. This manuscript introduces what we believe to be a novel solution in the form of a miniaturized pH sensor utilizing an assembly-free ball lens on a tapered multimode optical fiber (TMMF), offering the potential to revolutionize pH sensing in biochemical applications. A multimode optical fiber (MMF) was subjected to tapering processes, leading to the creation of an ultra-thin needle-like structure with a cross-sectional diameter of about 12.5 µm and a taper length of 3 mm. Subsequently, a ball lens possessing a diameter of 20 µm was fabricated at the apex of the taper. The resultant structure was coated utilizing the dip-coating technique, involving a composite mixture of epoxy and pH-sensitive dye, 2',7'-bis(2-carboxyethyl)-5-(and-6)-carboxyfluorescein (BCECF), thereby ensconcing the tapered ball lens with dye molecules for pH sensing. This study encompassed the fabrication and evaluation of six distinct fiber structures, incorporating the cleaved endface, the convex lens, and the ball lens structures to compare light focal lengths and propagation intensities. Computational simulations and numerical analyses were conducted to elucidate the encompassing light focal distances across the full array of lens configurations. The efficacy of the proposed pH sensor was subsequently assessed through its deployment within a complex liquid medium spanning a pH spectrum ranging from 6 to 8. Real-time data acquisition was performed with a fast response time of 0.5 seconds. A comparative analysis with a pH sensor predicated upon a single TMMF embedded with the fluorescent dye underscored the substantial signal enhancement achieved by the proposed system twice the fluorescence signal magnitude. The proposed assembly-free miniaturized pH sensor not only substantiates enhanced signal collection efficiency but also decisively addresses the persistent challenges of poor signal-to-noise ratio encountered within contemporary miniaturized pH probes.

Boosting SNR of cascaded FBGs in a sapphire fiber through a rapid heat treatment.

This Letter reports the performance of femtosecond (fs) laser-written distributed fiber Bragg gratings (FBGs) under high-temperature conditions up to 1600°C and explores the impact of rapid heat treatment on signal-to-noise ratio (SNR) enhancement. FBGs are essential for reliable optical sensing in extreme temperature environments. Comprehensive tests demonstrate the remarkable performance and resilience of FBGs at temperatures up to 1600°C, confirming their suitability for deployment in such conditions. The study also reveals significant fringe visibility improvements of up to ∼10 dB on a 1-m-long sapphire optical fiber through rapid heat treatment, representing a first-time achievement to the best of our knowledge. These enhancements are vital for improving the SNR and overall performance of optical fiber systems in extreme temperatures. Furthermore, the research attains long-term stability for the cascaded FBGs over a 24-hr period at 1600°C. This research expands our understanding of the FBG behavior in high-temperature environments and opens avenues for developing robust optical fiber systems for energy, aerospace, oil and gas, and high-temperature distributed sensing applications.

Large-scale cascading of first-order FBG array in a highly multimode coreless fiber using femtosecond laser for distributed thermal sensing.

This research focuses on the performance analysis and characterization of a fiber Bragg gratings (FBGs) array, consisting of 10 first-order FBGs inscribed by a femtosecond (FS) laser in a highly multimode coreless fiber. The study evaluates the FBG array's ability to function as a distributed thermal sensing (DTS) platform, with the coreless fiber chosen as the sensing element due to its immunity to dopant migration at high temperatures. The design of a large cascaded first-order FBG array effectively eliminates unwanted harmonic peaks across a wide spectrum range. In contrast, higher-order FBGs introduce limitations due to the overlapping of Bragg peaks with harmonics. The FBG array's performance is evaluated by measuring the reflection spectrum of each grating at different temperatures, showing a high temperature sensitivity of 15.05 pm/°C at a Bragg wavelength of 1606.3 nm, with a linear response in the temperature range of 24 - 1100 °C. The FBG array was designed for a spatial resolution of 5 mm. A mode scrambler in the sensing network is employed, which suppresses multimodal interference, characterizes FBG peak visibility, and stabilizes the interference spectrum. The stability of the FBG array is also assessed over 24 hrs at 1100 °C, and it is observed to be stable during thermal treatment. Heat treatment at 1100°C improves the signal to noise ratio of the FBG array, demonstrating the robustness and suitability of the proposed FBG array on highly multimode coreless fiber as a potential sensing platform for DTS applications in harsh environmental conditions, overcoming the issues of dopant migration presented by dopes silica optical fibers at high temperatures.

Highly cascaded first-order sapphire optical fiber Bragg gratings fabricated by a femtosecond laser.

This Letter reports an innovative technique for fabricating large-scale, highly cascaded first-order sapphire optical fiber Bragg gratings (FBGs) using a femtosecond laser-assisted point-by-point inscription method. For the first time, to the best of our knowledge, this study successfully demonstrates a distributed array of 10 FBGs within highly multimode sapphire crystal fiber, made possible by employing a high-power laser technique to generate larger reflectors with a Gaussian intensity profile. These first-order FBGs offer advantages such as enhanced reflectivity, shorter fabrication time, and simplified spectral characteristics, making them easier to interpret compared with high-order FBGs. The FBGs' resilience and effectiveness are analyzed by subjecting them to temperature tests, proving their capacity for accurate temperature monitoring up to 1500°C-a testament to their suitability for harsh environments. This novel approach broadens the scope for sensing and communication applications in sapphire fibers, particularly under challenging conditions. The novelty of our work lies in successfully overcoming the limitations of previous designs by integrating a cascade of 10 FBGs in sapphire fibers, thereby enhancing multiplexing capabilities, minimizing overlapping of FBG peaks, and ensuring reliable temperature monitoring in industries and applications with thermal gradients.

A Novel Non-Isolated High-Gain Non-Inverting Interleaved DC-DC Converter.

High-gain DC-DC converters are being drastically utilized in renewable energy generation systems, such as photovoltaic (PV) and fuel cells (FC). Renewable energy sources (RES) persist with low-level output voltage; therefore, high-gain DC-DC converters are essentially integrated with RES for satisfactory performance. This paper proposes a non-isolated high-gain non-inverting interleaved DC-DC boost converter. The proposed DC-DC converter topology is comprised of two inductors and these are charging and discharging in series and parallel circuit configurations. The voltage multiplier technique is being utilized to produce high gain. The proposed topology is designed to operate in three modes of operation. Three switches are operated utilizing two distinct duty ratios to avoid the extreme duty ratio while having high voltage gain. Owing to its intelligent design, the voltage stress on the switches is also significantly reduced where the maximum stress is only 50% of the output voltage. The proposed converter's steady-state analysis with two distinct duty ratios is thoroughly explored. Furthermore, a 160 W 20/400 V prototype is developed for performance analysis and validation. The converter topology can generate output voltage with a very high voltage gain of 20, which is verified by the prototype. Moreover, a high efficiency of 93.2% is attained by the proposed converter's hardware prototype.

Thermally robust and highly stable method for splicing silica glass fiber to crystalline sapphire fiber.

This research reports an advancement in splicing silica glass fiber to sapphire single-crystal optical fiber (SCF) using a specialized glass processing device, including data that demonstrate the thermal stability of the splice to 1000°C. A filament heating process was used to produce a robust splice between the dissimilar fibers. A femtosecond laser is used to inscribe a fiber Bragg gratings sensor into the SCF to measure the high-temperature capabilities and signal attenuation characteristics of the splice joint. The experimental results demonstrate that the proposed splicing method produces a splice joint that is robust, stable, repeatable, and withstands temperatures up to 1000°C with a low attenuation of 0.5 dB. The proposed method allows placement of SCF-based sensors in the extreme environments encountered in various engineering fields, such as nuclear, chemical, aviation, and metals manufacturing, to enable improvements in process monitoring, product quality, and production efficiency.

Highly Sensitive Strain Sensor by Utilizing a Tunable Air Reflector and the Vernier Effect.

A highly sensitive strain sensor based on tunable cascaded Fabry-Perot interferometers (FPIs) is proposed and experimentally demonstrated. Cascaded FPIs consist of a sensing FPI and a reference FPI, which effectively generate the Vernier effect (VE). The sensing FPI comprises a hollow core fiber (HCF) segment sandwiched between single-mode fibers (SMFs), and the reference FPI consists of a tunable air reflector, which is constituted by a computer-programable fiber holding block to adjust the desired cavity length. The simulation results predict the dispersion characteristics of modes carried by HCF. The sensor's parameters are designed to correspond to a narrow bandwidth range, i.e., 1530 nm to 1610 nm. The experimental results demonstrate that the proposed sensor exhibits optimum strain sensitivity of 23.9 pm/µÎµ, 17.54 pm/µÎµ, and 14.11 pm/µÎµ cascaded with the reference FPI of 375 µm, 365 µm, and 355 µm in cavity length, which is 13.73, 10.08, and 8.10 times higher than the single sensing FPI with a strain sensitivity of 1.74 pm/µÎµ, respectively. The strain sensitivity of the sensor can be further enhanced by extending the source bandwidth. The proposed sensor exhibits ultra-low temperature sensitivity of 0.49 pm/°C for a temperature range of 25 °C to 135 °C, providing good isolation for eliminating temperature-strain cross-talk. The sensor is robust, cost-effective, easy to manufacture, repeatable, and shows a highly linear and stable response for strain sensing. Based on the sensor's performance, it may be a good candidate for high-resolution strain sensing.

Three-Phase Six-Level Multilevel Voltage Source Inverter: Modeling and Experimental Validation.

This research proposes a three-phase six-level multilevel inverter depending on twelve-switch three-phase Bridge and multilevel DC-link. The proposed architecture increases the number of voltage levels with less power components than conventional inverters such as the flying capacitor, cascaded H-bridge, diode-clamped and other recently established multilevel inverter topologies. The multilevel DC-link circuit is constructed by connecting three distinct DC voltage supplies, such as single DC supply, half-bridge and full-bridge cells. The purpose of both full-bridge and half-bridge cells is to provide a variable DC voltage with a common voltage step to the three-phase bridge's mid-point. A vector modulation technique is also employed to achieve the desired output voltage waveforms. The proposed inverter can operate as a six-level or two-level inverter, depending on the magnitude of the modulation indexes. To guarantee the feasibility of the proposed configuration, the proposed inverter's prototype is developed, and the experimental results are provided. The proposed inverter showed good performance with high efficiency of 97.59% following the IEEE 1547 standard. The current harmonics of the proposed inverter was also minimized to only 5.8%.

Tapered multicore fiber interferometer for refractive index sensing with graphene enhancement.

An in-line, highly sensitive refractive index (RI) sensor based on a tapered multicore fiber (MCF) structure sandwiched between two single-mode fibers is proposed and demonstrated. The fiber tapering technique was employed to fabricate in-line interferometers based on the multicore fiber. The waist diameter is one of the dominant factors of the intercore coupling. The tapered MCF interferometer is highly sensitive to the surrounding refractive index with a maximum sensitivity of 9194.6 nm/RIU in the RI range of 1.4264 to 1.4278 when the waist diameter is 9 µm. The enhancement of the evanescent field by graphene coating is proved to be able to improve the RI sensitivity further. A graphene-coated MCF interferometer with waist diameter of 9 µm offers the maximum sensitivity of 12617.6 nm/RIU in the RI range of 1.4144 to 1.4159. The experimental data have good agreement with the simulated results.